TP-Link Deco X50 AX3000 — 3-pack
Three Gigabit ports on each unit give a TV, console or desktop somewhere to plug in, while Ethernet between nodes can make coverage more consistent in distant rooms. It is a sensible starting point for streaming, calls and everyday use on a 50–500 Mbps plan. Its ports limit faster connections, so compare the BE25 if you are moving beyond Gigabit Ethernet. When their prices are close, the choice comes down to the X50’s extra port versus the BE25’s faster ones.
Specifications
| Pack | Three standard Deco X50 units |
|---|---|
| Wireless | Dual-band Wi-Fi 6, 2.4 and 5 GHz |
| Advertised PHY rates | Up to 574 Mbps on 2.4 GHz and 2,402 Mbps on 5 GHz under compatible conditions |
| Ethernet | Three Gigabit auto-sensing WAN/LAN ports per unit |
| Backhaul | Ethernet or shared dual-band wireless |
| Modes | Router or access point |
| Setup | Deco app and TP-Link ID |
| Main-node spare ports | One Gigabit port after WAN and one directly wired satellite in router mode |
| NBN connection | Ethernet WAN. FTTN/FTTB require a separate compatible VDSL2 modem |
| Hardware support | Match the physical hardware version to the Australian firmware branch |
| Security | WPA3 support, with HomeShield features varying by mode and plan |
| Warranty | Three-year limited warranty for eligible purchases from authorised Australian retailers; conditions apply. |
Further product analysis
Everyday performance and speed limits
The X50 suits homes that need a better signal in the study, lounge or upstairs without paying for more wireless capacity than their equipment can use. Its Gigabit Ethernet ports leave room for common home devices. On a 1 Gbps plan, Ethernet overhead and the rest of your connection will reduce usable speed below the port’s nominal rate. A weak wireless hop can bring the speed down further. For an NBN 2000 service or large transfers to a multi-gig NAS, choose a system with faster wired ports.
Placement and wired connections
A wired node leaves more wireless capacity for phones and laptops. Without Ethernet, the same radio bands carry client traffic and traffic between nodes. Put the second unit somewhere it can still get a good connection to the first, then add the third where testing shows it helps. A node placed in the room with the weakest signal can inherit the same problem you bought mesh to solve.
Setup, support and ownership
See the NBN setup advice for app, account and access-point setup. Check the hardware version on your units before installing firmware or assuming a particular advanced feature is available.
When to choose another pick
The X50 is the better fit when you want an extra port for ordinary wired devices and your connection fits within Gigabit Ethernet. The BE25 is worth comparing when you need a faster wired path. The BE65 adds more fast ports and 6 GHz, with less reason to pay for it if the task is simply reaching the spare bedroom. Use Australian X50 support and select the version printed on the unit when checking updates.
Pros
- Three useful Gigabit ports per unit.
- Ethernet backhaul works with a wired house.
- Good fit for the plans and devices many households already use.
Cons
- Gigabit ports limit faster fibre and multi-gig local networking.
- Shared wireless backhaul can cut throughput in hard-to-reach rooms.
- App and account required for initial setup.
TP-Link Deco BE25 BE5000 — 3-pack
That is useful if you want a faster NBN connection or wired link to another room and have only a few devices to plug in. The catch is the port count. Connecting the internet and one wired satellite uses both ports on the main unit, so extra wired connections need a switch or a different layout. It also has no 6 GHz band. Choose it for the faster wired path and check that its two ports per node suit your setup.
Specifications
| Pack | Three standard indoor Deco BE25 BE5000 units |
|---|---|
| Wireless | Dual-band Wi-Fi 7 on 2.4 and 5 GHz |
| Advertised PHY rates | Up to 688 Mbps on 2.4 GHz and 4,324 Mbps on 5 GHz; TP-Link warns that 240 MHz operation on 5 GHz may be unavailable in Australia. These are theoretical link rates, not internet speeds |
| Ethernet | Two 2.5GbE auto-sensing WAN/LAN ports per unit |
| Backhaul | Wired Ethernet or shared dual-band Wi-Fi |
| Operating modes | Router or access point |
| Setup | Deco app and TP-Link ID |
| Main-node spare ports | None after WAN and one directly wired satellite in router mode |
| Adding a second wired satellite | Use a suitable switch or chain through the first satellite’s spare port |
| NBN connection | Ethernet WAN. FTTN/FTTB require a separate compatible VDSL2 modem |
| Hardware support | Match the physical hardware version and region before updating |
| Security | WPA3 support and optional paid HomeShield features |
| Warranty | Three-year limited warranty for eligible purchases from authorised Australian retailers; conditions apply. |
Further product analysis
Faster Ethernet and the two-port compromise
The two faster ports are the reason to buy it. Connect one to a compatible NBN box and one to a wired satellite, and both ports on the main unit are in use. The satellite has one spare for a computer or another wired device. If you want to wire two satellites directly from the main unit, budget for a switch. You can instead chain the second satellite through the first, but that uses the first satellite’s remaining port. Use a 2.5GbE switch if you need those links to run faster than Gigabit.
Wireless placement and Australian limits
Without Ethernet between nodes, the same bands serve your devices and carry traffic between rooms. The BE25 has no 6 GHz band, so its strengths are simpler wired setups and wireless nodes that can still get a strong signal. A wired node is worth prioritising across thick walls or for rooms where you care about steady latency. TP-Link warns that 240 MHz operation on 5 GHz may be unavailable in Australia. Multi-Link Operation depends on your equipment and settings. It won’t fix a poor link between nodes.
Setup, support and customer evidence
Owner feedback includes setup recoveries and complaints about paid parental or security features, alongside positive coverage reports. See the NBN setup advice if you need to keep a modem or ISP gateway, and match firmware to the label on your unit.
When to choose another pick
Choose the X50 when everyday coverage and an extra Gigabit port matter more than faster Ethernet. Step up to the BE65 when you need more fast wired connections. For a setup without cabling between rooms, read the wireless-only buying advice before paying for faster ports.
Use Australian BE25 support and match the hardware version and region on the unit.
Pros
- Two 2.5GbE ports on every node.
- Lower-cost entry to wired multi-gig mesh than the BE65.
- Works with wired and wireless nodes.
Cons
- No spare port on the main unit after WAN and one wired satellite.
- No 6 GHz band, and wireless backhaul shares airtime with devices.
- Initial setup requires the Deco app and a TP-Link account.
TP-Link Deco BE65 BE11000 — 3-pack
You can connect the internet and one satellite to the main unit and still have two ports spare. Its extra 6 GHz band also gives compatible devices another wireless option when the signal between rooms is strong. That flexibility earns its place in a wired home or a setup with several fast devices. Check that you are buying the Australian BE11000 pack and match firmware to the hardware label, because the BE65 name also covers a BE9300 version.
Specifications
| Pack | Three Deco BE65 BE11000 units. Confirm the box and hardware revision. |
|---|---|
| Wireless | Tri-band Wi-Fi 7, 2.4, 5 and 6 GHz |
| Wi-Fi 7 features | 320 MHz on 6 GHz and Multi-Link Operation on compatible devices |
| Ethernet | Four 2.5GbE auto-sensing WAN/LAN ports per node |
| Backhaul | Ethernet and tri-band wireless support |
| Modes | Router or access point |
| Setup | Deco app and TP-Link ID |
| Main-node spare ports | Two 2.5GbE ports after WAN and one directly wired satellite in router mode |
| NBN connection | Ethernet WAN. FTTN/FTTB require a separate compatible VDSL2 modem |
| Hardware support | Australian BE11000 pack. Select the correct branch for the physical hardware label |
| Security | WPA3 support and optional paid HomeShield features |
| Warranty | Three-year limited warranty for eligible purchases from authorised Australian retailers; conditions apply. |
Further product analysis
More fast ports
The port layout is the main reason to step up. You can connect the main Deco to a compatible multi-gig NBN box, run Ethernet to a satellite and still have ports available for a switch or a local device. To see more than a gigabit, every link on that path must support it. The four 2.5GbE ports are individually rated. They do not combine into one faster internet link.
Wireless links and placement
The extra 6 GHz band can help compatible devices and wireless backhaul when nodes have a good signal. Solid walls and floors are a different story. Start with the nodes in open locations and measure at the places where you work or stream. Run Ethernet between floors if you can. In router mode, connect wired satellite units downstream of the main Deco. If the app shows a node using wireless despite a cable, test a known-good cable and a direct connection before changing the whole network.
ISP setup and reported problems
Check your provider’s WAN settings first. Keep your working gateway available during setup, especially if you use an ISP phone service. See the NBN setup advice for using access-point mode behind your provider gateway.
Hardware versions and purchase fit
TP-Link also lists a BE9300-labelled BE65 version. Its Australian BE11000 specifications warn that 240 MHz operation on 5 GHz may be unavailable locally. Check the box and update only through the Australian support path for your hardware version.
The BE65 earns its premium through connection flexibility. It is easier to justify with fast wired devices than in a home where most use is streaming over a modest NBN plan. For that simpler task, the X50 or BE25 can be the more sensible purchase. Use Australian BE65 support and choose the hardware branch on the physical label. The support page’s default branch can refer to the BE9300 version.
Pros
- Four multi-gig ports on every unit.
- Tri-band Wi-Fi with 6 GHz and wired backhaul support.
- Useful headroom for fast NBN or local transfers.
Cons
- Costs more than an everyday coverage upgrade.
- Setup and roaming experience can vary with ISP, firmware and client.
- Strong 6 GHz performance depends on the link between rooms.
Other mesh systems we assessed
See other mesh systems assessed
ASUS ZenWiFi BD4 three-pack — Offers browser-based control and two 2.5GbE ports per unit. Too few verified owner ratings for the exact Australian pack kept it out of the featured picks.
TP-Link Deco X50-PoE three-pack — Useful for ceiling or wall placement with suitable power-over-Ethernet equipment. Its single 2.5GbE port limits faster wired layouts, and the exact pack lacked sufficient verified owner ratings.
TP-Link Deco XE75 non-Pro three-pack — A 6 GHz alternative for buyers who do not need faster Ethernet. It meets the rating minimum, but its Gigabit ports limit faster wired connections and we established no current-revision reliability advantage.
eero Pro 7 three-pack and ASUS ZenWiFi BT8 two-pack — The eero favours simple app management; the ASUS offers more local control. Neither exact Australian pack had enough verified owner evidence for an award.
TP-Link Deco XE75 Pro and BE85 — The XE75 Pro’s single 2.5GbE port cannot serve both faster internet and faster wired backhaul in router mode. The BE85’s faster ports are a specialist step beyond the everyday and 2.5GbE needs covered here.
What to check before buying
Buying advice
Check whether you need mesh
Try moving your existing router into the open first. An extender may suit one nearby weak room; mesh is worth considering when several rooms need coverage. Each mesh unit needs a strong connection to the rest of the system.
Plan placement and connections
Ethernet between units makes the connection less dependent on walls and floors. Without cabling, place additional units where they still receive a strong signal, rather than in the dead spot. All three kits work wirelessly, but faster Ethernet ports do not establish better wireless coverage.
Match speed and spare ports
Your plan, internet port, connection between units and receiving device can each limit speed. Gigabit Ethernet is rated at 1Gbps; 2.5GbE at 2.5Gbps. Actual results are lower or variable. Count the ports left after connecting the internet and any wired mesh units, and include a suitable switch in the total price if needed.
Keep the right modem and phone setup
FTTN and FTTB need a compatible VDSL2 modem; FTTP, HFC and FTTC typically provide Ethernet from an NBN box. Check your provider’s settings and phone-service requirements before replacing its gateway. Deco access-point mode lets an existing router keep routing, with some Deco features unavailable. Initial setup requires the Deco app and a TP-Link account; some advanced security and parental controls cost extra.
Compare total cost and support
Compare delivered prices for the exact three-packs, including any switch or cabling. Pay for faster ports or an extra wireless band only when your setup can use them. Eligible purchases from authorised Australian retailers carry TP-Link’s three-year limited warranty. Keep your receipt and serial number; retail claims generally go through the seller and may require TP-Link troubleshooting first. Australian Consumer Law rights are additional.
Which one should you buy?
TP-Link Deco X50 AX3000 three-pack — Choose this for everyday coverage, streaming and calls when Gigabit Ethernet meets your needs. Its three ports per unit give ordinary wired devices more connection options.
TP-Link Deco BE25 BE5000 three-pack — Choose this when faster Ethernet solves a real bottleneck and you need relatively few wired connections. Include the cost of a suitable switch if its two ports per unit will not be enough.
TP-Link Deco BE65 BE11000 three-pack — Choose this when several fast wired connections justify the extra spend, or compatible devices can use its additional 6 GHz band. Confirm the Australian BE11000 pack and hardware version.
How we chose
Detailed methodology
We compared the exact Australian three-packs for NBN compatibility, ports, node connectivity, setup, update paths and value. Manufacturer speeds and area claims describe specified conditions. Independent measurements show what happened in a particular test. Owner reports help identify repeat problems and things to check during setup. We kept these evidence types separate.
Customer stars are separate from the WBA editorial score. We screened retailer records for the exact pack, conservatively counted overlapping owner records once, and kept retailer pools separate. Hardware revision and firmware are often missing from customer reviews, so the customer panel describes the listing rather than one firmware build.
Customer evidence behind the panels
Customer ratings use screened records for the stated Australian pack, with overlapping records counted once.
Some ratings may be incentivised. Hardware revisions are not identified in every review.
Netgear Orbi 770 RBE773: Check the original or v2 label before downloading any firmware.
Frequently asked questions
Will a mesh router replace my NBN modem?
For an Ethernet hand-off, it can usually act as your router if your provider supports BYO equipment and you enter the correct settings. For FTTN or FTTB, keep a compatible VDSL2 modem in the setup. If your home phone depends on the ISP gateway, ask your ISP what needs to stay connected.
Can I use mesh with my existing router?
Yes. Access-point mode lets the existing router keep handling the internet connection and addressing. Mesh features that depend on the mesh system doing the routing may be unavailable. If both devices are routing, double NAT can complicate gaming, inbound access and some VPN setups.
Will a Wi-Fi 7 mesh give me the full speed of NBN 2000?
It can provide a suitable path if the NBN box, WAN port, backhaul and device all support multi-gig speeds. Expect results to vary by room, client and congestion. A 2.5GbE port is a link rating and Wi-Fi class numbers add up multiple bands.
Should I start with two nodes or three?
This guide assesses the named three-packs. You do not have to deploy all three supplied units: start with two if they cover the rooms that matter, then add the third where testing identifies a gap and it can maintain a good connection. If buying a smaller pack instead, check its exact model, contents and delivered price separately; this guide has not assessed that purchase.
Do I need Ethernet between nodes?
Wireless works when the nodes can hear each other well. Ethernet is worth prioritising when there are thick walls or floors between them, or when you want more predictable speed and latency in a distant room.
Why does my phone stay connected to the wrong node?
The phone decides when to roam, although the mesh can guide it. Check node spacing and firmware. If an older device drops during handover, test whether disabling Fast Roaming helps that device before changing other settings.
What’s the difference between the BE25 and BE65?
Both have 2.5GbE ports. On the BE25, connecting the NBN box and one wired satellite fills the main unit’s ports. The BE65 leaves two spare ports in that setup and adds 6 GHz. Choose the BE25 if you need the speed with fewer connections.
Do I need a subscription?
The recommended Deco kits provide basic routing and Wi-Fi without a paid HomeShield plan. Some advanced security and parental-control features cost extra. Check the current feature list for your model and operating mode.
